Japan Sancolor SP-751 cleaning agent

　　 Origin: Japan
　　 Manufacturer: Sancai Chemical Co., Ltd.
　　 Brand: Sancai
　　 Model: SP-751
　　 Capacity: 20kg
　　Applicable performance:
Ceramic anilox rollers are key components in flexographic printing presses, offset printing presses and glazing units, corrugated box printers, coating machines and other equipment. In the process of printing, glazing, and coating, water-based inks, varnishes, and coatings are used. Often a solidified layer is gradually formed in the cells of the anilox roll to block the cells, thereby affecting the effects of printing, glazing and coating. The solidified layer that blocks the cells is generally difficult to clean from the cells.
Japan's three-color anilox roller cleaning agent, it is characterized by easy to use, effective, without any auxiliary settings, in a relatively short time, it can remove the ink, varnish, paint and other cured layers in the cell, and restore it to one A clean ceramic anilox roller maintains its original ink transfer and coating effects.
　　 Instructions for use of cleaning agent:
Dry laminating (used for gluing coating, commonly known as GRAVURE ROLL). After the daily operation, the gluing tank and circulation pump should be cleaned together (except for the 24-hour operation). However, it is very difficult to clean the adhesive completely with ethyl acetate. A small amount of adhesive will still remain on the rubber wheel. Such repeated siltation will result in blockage. Once the adhesive stuffed in the mesh is hardened, it cannot be dissolved in ethyl acetate, let alone the cleaning effect.
However, the operation of the rubber wheel on the stopper state will cause problems due to insufficient coating amount, such as poor appearance (with bubbles) and poor adhesive strength. Most of the causes are due to use The problem of insufficient coating amount caused by the rubber wheel of the plug plate. In order to prevent the continuous occurrence of such problems, NEO REVER should be used to clean the rubber wheels in order to obtain the proper coating amount.
　　 Here are the steps and precautions for using the washing solution as follows:
  Steps:
　　 1. First, clean the glue groove and the glue wheel with ethyl acetate.
　　 2. Spread 3-4 sheets of film in the glue tank. (OPP, PET, CPP, LLDPE are all available)
　　3. Start the rubber wheel idling, and at the same time apply the washing liquid to the rubber wheel, and leave it for 5-10 minutes (the hardened glue will be quickly absorbed to the surface of the wheel).
　　4. Brush the metal brush against the rubber wheel mesh vertically and vigorously, and wash it back and forth 2-3 times.
　　5. If there is still something unclean in the depth of the plate, continue cleaning with metal again.
　　 6. Use 2-3 kg of ethyl acetate with a metal brush, and pour the ethyl acetate onto the rubber wheel to wash off the washing liquid on the rubber wheel.
　　7. Remove the washing liquid and adhesive residues washed into the tank together with the film and discard.
8. Inject 10 kg of ethyl acetate into the tank, and make the rubber wheel contact with the state, while idling the rubber wheel, while using a metal brush or a clean cloth to clean it, until the foreign matter in the plate is washed. .
　　 9. Repeat the above eighth and ninth operation procedures again, this is to prevent the washing liquid from remaining.
　　10. Pour the rubber wheel with 3-5 liters of ethyl acetate, and test the rubber wheel with a rag.
　　 11. Wipe the rubber wheel again with a clean, dry cloth.
　　 12. Take out the ethyl acetate and the substrate film in the tank and discard it to complete the operation.
The cleaning operation time is 30 minutes. It is very necessary to clean the rubber wheels with the plate washing solution once a week or once every two weeks. (The frequency of cleaning depends on the daily maintenance. If you often use ethyl acetate for cleaning and maintenance, you can clean it with a plate cleaner once every two weeks. It also depends on the amount of coating. And appearance condition).